Precision Fluid Dispensing Pump, Model M3000 & M2000; Semiconductor Equipment

Internet Cash Machines

Our site is
http://gonow.to/olmenterprises
gonow.to easy to remember web address service

Easy to reach, Easy to remember!

High Precision Fluid Dispensing Pump, Models M3000 & M2000

M3000 & M2000

The M3000 and M2000 are stand-alone pump, motorized fluid delivery systems designed to support multi-nozzle delivery of accurate, repeatable shots over a presettable volume range. The systems are fully programmable. The standard configuration includes one pump module, but configurations of two and four pump module are also available - all built onto a common frame. The systems are built for demanding applications that require performance and adaptability.The M3000 uses sliding valve - pump modules. The M2000 uses check ball - valve pump modules.

Both the M3000 and M2000 are designed for applications as diverse as pharmaceuticals, biotechnology, semiconductor fabrication and assembly, medical dispensing, food production . . . virtually any, manufacturing or laboratory environment where repeatability and accuracy must be maintained. And because the systems incorporate FDA-compliant such as 316SS, Polyethylene & Alumina ceramic wetted components, they can be designed into many liquid applications where purity of the medium is critical.

Note: All information contained in this website is subject to engineering change without notice.
Teflon® and Viton® are registered trademarks of DuPont Dow Elastomers.

M3000 SPECIFICATIONS

PUMP MODULE	PISTON DIA.	PRESETTABLE SHOT RANGE	FLUID PRESSURE, MAX	FLUID INLET TUBE DIA.	FLUID OUTLET TUBE DIA.
ML1608	0.5 in	0.5 - 2.9 ml	400 psig.	3/8 in	3/8 in
ML1616	1 in	3.5 - 11.5 ml	100 psig.	3/8in	3/8 in

Valve Type	: Sliding
Viscosity	: 100,000 cp
Piston Stroke	: 1 in
Stroke Adjustment	: .001 Resolution Micrometer
Operating Cycle (fixed)	: 72 cycles/min
Accuracy	: 99.9%
Repeatability	: 99.7%
Piston Material	: Alumina Ceramic
Wetted Material	: Polyethylene, 316SS, Ceramic, Viton, Teflon
Pump Module Dimensions	: 2 in (dia.) x 18 in
Weight	: 8.5 lbs.
Electrical Requirements	: 110 VAC, 60Hz
Max. Pumps Per System	: 4

Controllers	: SAC 2000
	CLC 2000

Repeatability is the measure of the consistency of shot volume delivery, obtained by calculating the ratio of any shot volume to the average shot volume of a particular pump stroke setting multiplied by 100.

Accuracy is determined by comparing actual shot volume to the preset shot volume, calculated as the quotient of the actual shot volume to the preset shot volume, multiplied by 100.

Data in website is based on tests performed using water as the pumping media.

PATENTED

Teflon® is a registered trademark of Dupont.

Viton® is a registered trademarks of DuPont Dow Elastomers.

SEE FEATURES

To Order or for Additional
Information:

E-mail: webmaster@semiconweb.net

M3000 FEATURES

Pump module is easy to maintain and clean

Autoclavable pump components

Adaptable for remote operation

Minimum dead volume for easy priming

Purging with minimum effort

Programmable, presettable shot volume

Clean material cut-off

Micrometer adjustable at .001 in resolution

Relay or PLC controller abvailable

SEE SPECIFICATIONS

M2000 SPECIFICATIONS

PUMP MODULE	PISTON DIA.	PRESETTABLE SHOT RANGE	FLUID PRESSURE, MAX	FLUID INLET TUBE DIA.	FLUID OUTLET TUBE DIA.
MPL1608	0.5 in	0.5 - 3.5 ml	400 psig.	3/8 in	1/4 in
MPL1616	1 in	3.5 - 12.5 ml	100 psig.	3/8in	3/8 in

Valve Type	: Check Ball
Viscosity	: 5,000 cp
Piston Stroke	: 1 in
Stroke Adjustment	: .001 Resolution Micrometer
Operating Cycle (fixed)	: 72 cycles/min
Accuracy	: 99.9%
Repeatability	: 99.7%
Piston Material	: Alumina Ceramic
Wetted Material	: Polyethylene, 316SS, Ceramic, Viton, Teflon
Pump Module Dimensions	: 2 in (dia.) x 18 in
Weight	: 8.5 lbs.
Electrical Requirements	: 110 VAC, 60Hz
Max. Pumps Per System	: 4

Controllers	: SAC 2000
	CLC 2000